iss 1 c1u date 21-7-2011 saw bandpass filter part no.: ACTF9194-1950-DCC6C features ? low-loss rf filter for mobile systems ? low amplitude ripple ? no matching network required for operation at 50 ? ? ceramic package for s urface m ounted t echnology ( smt ) ? lead-free production and rohs compliant package dimensions ceramic package: dcc6c pin configuration 2 input 5 output 1, 3, 4, 6 ground marking top view, laser marking " act ?: manufacturer?s mark ?f ?: saw filter ? 9194 ?: part number ? ?: terminal 1 ??: lot number (the code shown below varies in a 4-year cycle) code 1 2 3 4 5 6 7 8 9 10 11 12 2009 a b c d e f g h j k l m 2010 n p q r s t u v w x y z 2011 a b c d e f g h i j k m 2012 n p q r s t u v w x y z actf 9194*
iss 1 c1u date 21-7-2011 maximum ratings rating value unit input power level p 10 dbm dc voltage v dc 12 v operating temperature range t a -40 ~ +85 c storage temperature range t stg -40 ~ +85 c electrical characteristics item minimum typical maximum unit center frequency f c 1950 mhz insertion loss il 1920.00 ?. 1980.00 mhz -- 1.8 ** 2.5 *( db group delay ripple 1920.00 ?. 1980.00 mhz 10 ** 40 ns absolute attenuation dc ?. 1400.00 mhz 22 25 db 1400.00 ?. 1495.00 mhz 25 27 db 1495.00 ?. 1700.00 mhz 25 27 db 1700.00 ?. 1870.00 mhz 28 30 db 1870.00 ?. 1880.00 mhz 23 *( 31 db 2000.00 ?. 2015.00 mhz 4.0 *) 9.0 db 2015.00 ?. 2030.00 mhz 22 45 db 2030.00 ?. 2050.00 mhz 35 45 db 2050.00 ?. 2080.00 mhz 33 36 db 2080.00 ?. 2170.00 mhz 28 30 db 2170.00 ?. 3000.00 mhz 25 30 db amplitude ripple (p-p) 1920.00 ?. 1980.00 mhz ? 0.6 ** 1.2 db intput vswr 1920.00 ?. 1980.00 mhz 1.5 1 2.01 output vswr 1920.00 ?. 1980.00 mhz 1.5 1 2.01 input / output impedance (nominal) 50 ? rohs compliant *) : -40 ** : +25 *( : +85 electrostatic sensitive device
iss 1 c1u date 21-7-2011 typical frequency response
iss 1 c1u date 21-7-2011
iss 1 c1u date 21-7-2011 stability characteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m 2 vibration resistance (a) frequency of vibration: 10~55hz (b) amplitude: 1.5 mm (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40c, 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) + 70c for 16 hours (b) +55c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high temperature exposure (a) temperature: 70c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70c for 30 minutes ? -25c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements: the saw filer shall remain within the electrical specifications after tests. remarks ? saw devices should not be used in any type of fl uid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exce eding the rated voltage of components. ? do not operate outside the recommended oper ating temperature range of components. ? sudden change of temperature shall be avoided, deterioration of the char acteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering ir on on the body of components. ? be careful not to subject the terminals or leads of components to excessive force. ? saw devices are electrostatic sensitive. please avoi d static voltage during operation and storage. ? ultrasonic cleaning shall be avoided. ultrasonic vi bration may cause destr uction of components. test circuit recommended land pattern
iss 1 c1u date 21-7-2011 carrier tape reel dimensions outer packing type quantity dimension description weight carton box 10000 19019095 0.85 carton box 20000 190190190 anti-static plastic bag & carton box 1 reel / bag 5 bags / box (10000 pcs) 10 bags / box (20000 pcs) 1.80 unit: mm unit: kg recommended soldering profile 1. the specifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and governm ent approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wa ve (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies.
|
